Technical resources / Application guides

INCISE WB Sealer

Protect the finish. Preserve its natural character.

A step-by-step guide to preparing, applying and curing INCISE WB Sealer for a clear, considered finish.

View the steps Ask INCISE
Single componentReady to use
2 - 3 coatsThin and even
8 - 12 m²/LPer coat
5 - 7 daysFull cure

What is INCISE WB Sealer?

INCISE WB Sealer is a single-component, water-based protective sealer for concrete, stone, terrazzo, microcement and compatible wood surfaces. It enhances the natural appearance of the substrate with a transparent matte or satin finish, as specified, without heavy film build.

Ready to use; water-based, low VOC formulation; low odour; excellent adhesion to porous substrates; good abrasion resistance; UV stability for interior and protected exterior use; fast drying and easy recoating.

Where can INCISE WB Sealer be used?

Decorative microcement floors and walls; polished or power-floated concrete; terrazzo; timber flooring and wooden elements; residential interiors; light commercial spaces; retail and hospitality projects.

Good resistance to household chemicals; improved stain resistance; moderate abrasion resistance; slight enhancement of colour depth; a breathable film that allows moisture vapour transmission. For high chemical exposure or heavy commercial use, refer to INCISE PU Sealer systems.

A good seal begins with preparation.

Concrete and terrazzo

The surface must be clean, dry and structurally sound. Remove dust, laitance, grease, curing compounds and contaminants. Mechanically abrade smooth surfaces if necessary. Moisture content should be below 5%.

Microcement

Allow the microcement to cure fully, then lightly sand. Remove all dust and ensure the surface is free from waxes and other contaminants.

Wood

The surface must be clean, sanded and dry. Remove old coatings unless compatibility is established. Timber moisture must not exceed the recommended level for the wood system.

Choose the right tools

Prepare a microfiber or short nap roller, a brush for corners and edges, a clean stirring tool and a roller tray. Remove sanding dust before application. Spray equipment may be used where required. Keep clean water ready for immediate tool cleaning.

Application sequence

Thin coats. Consistent protection.

Read the product TDS and SDS before starting.

Step 01

Check and prepare the substrate

Choose the preparation method for your substrate. Concrete and terrazzo must be sound, clean and dry, with moisture below 5%. Microcement must be fully cured and lightly sanded. Wood must be sanded and dry, with incompatible old coatings removed. Remove all dust before sealing.

Step 02

Stir the ready-to-use sealer

Stir INCISE WB Sealer thoroughly before use. It is single component: no hardener is added. Do not dilute unless specified by INCISE. The liquid appears milky and dries transparent. Confirm the specified matte or satin finish before application.

Step 03

Apply the first thin coat

Use a microfiber or short nap roller across the main surface and a brush at edges and corners. Spray application may be used where required. Apply a thin, even coat; avoid over-application, which can cause excessive film build or whitening. Work between +10°C and +30°C and do not apply above 80% relative humidity.

Step 04

Recoat to complete the system

Typically apply 2 - 3 thin coats, depending on the performance requirement. Allow the applicable recoat interval between coats. Recoat timing requires confirmation: the supplied technical table states 2 - 4 hours, while its packaging/application note states 4 - 12 hours. Confirm the applicable interval with INCISE before recoating.

Step 05

Protect, cure and maintain

Typical light foot traffic is 12 - 24 hours; full cure is 5 - 7 days. Avoid direct rain for the first 24 hours and protect from rain and condensation during curing. Clean tools immediately with clean water; hardened sealer requires mechanical removal. Clean sealed surfaces with pH-neutral cleaners. Avoid abrasive pads and harsh solvents. Re-sealing may be required in high-wear environments after several years; the actual interval depends on use and condition.

How much WB Sealer do you need?

8 - 12 m² per litre per coat, depending on substrate porosity. A 5 L pack covers approximately 40 - 60 m² in one coat; a 20 L pack covers 160 - 240 m² in one coat. For two coats, allow approximately 0.17 - 0.25 L/m²; for three coats, 0.25 - 0.375 L/m², before wastage. Confirm yield on the actual substrate.

Respect the exposure limits

Do not apply to wet substrates or substrates affected by rising damp. Do not apply above 80% relative humidity. Avoid direct rain exposure for the first 24 hours and protect from rain and condensation during curing. Not recommended for permanent or continuous water immersion. Not suitable for heavy industrial traffic without additional protection. Professional application is recommended.

Questions before you seal.

Does INCISE WB Sealer need a hardener?

No. It is single component and supplied ready to use. Stir thoroughly and do not dilute unless specified.

Will WB Sealer change the surface colour?

The milky liquid dries transparent and may slightly enhance colour depth. Matte and satin finishes are available as specified. Assess the appearance on a sample of your substrate.

How long does WB Sealer take to dry?

Typical touch dry is 1 - 2 hours, light foot traffic 12 - 24 hours, and full cure 5 - 7 days. Recoat timing requires confirmation: the supplied technical table states 2 - 4 hours, while its packaging/application note states 4 - 12 hours. Confirm the applicable interval with INCISE before recoating.

Can WB Sealer be used in permanently wet areas?

It is not recommended for permanent or continuous immersion. Do not apply over rising damp or wet substrates.

How do I maintain a sealed surface?

Clean sealed surfaces with pH-neutral cleaners. Avoid abrasive pads and harsh solvents. Re-sealing may be required in high-wear environments after several years; the actual interval depends on use and condition.

Match the sealer to your project.

Tell INCISE your substrate, area and expected use. The team can help you confirm whether WB Sealer or a PU Sealer system is appropriate.

Contact INCISE Technical resources

Images are illustrative application visualisations.