Technical / Application guide
INCISE Silicon Sealer
Protect the surface. Preserve its character.
A clear, penetrating water repellent for porous mineral surfaces. Follow the INCISE Silicon Sealer application guide for preparation, saturation and curing.
Follow the applicationNatural protection
What is INCISE Silicon Sealer?
INCISE Silicon Sealer is a water-based, silane/siloxane penetrating hydrophobic sealer for porous mineral surfaces. It penetrates the capillary network and chemically bonds within the pores to reduce water absorption while maintaining water-vapour permeability. It provides invisible, natural protection without forming a surface film.
Where can it be used?
Suitable for vertical and horizontal porous mineral surfaces including: fair-faced concrete; cement screeds; precast concrete panels; microcement finishes; brickwork; natural stone; terrazzo; exposed aggregate finishes; masonry facades; boundary walls; parking structures; balconies (non-traffic areas); decorative paints and lime plasters; architectural facades; coastal structures; limewash; decorative coatings and paints. Decorative finishes must remain porous and compatible with the penetrating treatment; confirm absorption and appearance on a sample first. Non-porous or already sealed finishes are unsuitable.
What makes it different?
Designed for high-rainfall exposure, efflorescence control, coastal salt protection and facade durability. Deep penetration and hydrophobic action reduce capillary water absorption and dirt pickup while allowing the substrate to breathe. UV and alkali resistance support long-term substrate durability. This treatment is not a traffic-bearing finish.
Prepare your tools
Use a low-pressure sprayer, roller or brush, suitable surface-cleaning tools, masking and protective sheets. Wear suitable gloves, eye protection and work clothing. Ensure adequate ventilation and follow the product safety instructions.
Step 01
Assess and test
Confirm that the surface is porous, mineral and unsealed. Test INCISE Silicon Sealer on a discreet area to confirm absorption, appearance and consumption. Check the forecast and work only between +5°C and +35°C. New concrete must be at least 28 days old.
Step 02
Prepare the surface
Remove dust, dirt, oil, grease, laitance and previous coatings. Mechanically clean where required, repair cracks and allow the substrate to dry. Protect neighbouring materials from splashes. Surface preparation determines how evenly the treatment can penetrate.
Step 03
Apply evenly
Do not dilute. Apply INCISE Silicon Sealer evenly with low-pressure spray, a roller, or a brush for small and detailed areas. Bring the porous substrate to saturation without allowing pooling. Use controlled passes and avoid overspray.
Step 04
Complete details and saturation
Use a brush around edges and detailed areas. If the substrate requires a second coat, apply it wet-on-wet. Judge demand from the test area and substrate absorption; do not treat the normal 4–8 m²/L range as a fixed spread rate for every surface.
Step 05
Protect, cure and review
Protect the treated surface from rain during curing. Touch drying normally takes 1–2 hours; water repellency develops over 24–48 hours. Review the completed treatment against the approved test area. The surface should retain its natural appearance, without a coating film.
Plan coverage. Allow time.
4–8 m²/L
Typical coverage. Porosity, saturation demand and any wet-on-wet second coat affect consumption.
5 L / 20 L
Container sizes. Indicative yield: 20–40 m² or 80–160 m², before additional demand and wastage.
24–48 hours
Water-repellency development. Touch dry in approximately 1–2 hours. Protect from rain during curing.
Store unopened in cool, dry conditions out of direct sunlight. Shelf life: 12 months from manufacture.
Before you specify.
Does Silicon Sealer leave a glossy coating?
INCISE Silicon Sealer is non-film-forming and designed to retain a natural appearance. Always approve a test area on the actual substrate.
Can I apply it over paint or another sealer?
Generally no. Painted and sealed surfaces are excluded. For a porous mineral decorative finish, including a suitable lime plaster, ask INCISE to confirm compatibility before application.
Is it a traffic-bearing floor finish?
No. Although suitable porous horizontal surfaces are listed, INCISE Silicon Sealer is not a traffic-bearing finish. Ask INCISE to specify the appropriate system for a trafficked area.
Should it be diluted or left to dry between coats?
Do not dilute. If a second coat is required, apply wet-on-wet as instructed. Do not substitute a dry-between-coats process.
Can I apply it before rain?
Do not apply during rain. Schedule a dry weather window and protect the surface from rain during curing. Repellency develops over 24–48 hours.
Specify with confidence
Start with your substrate.
Tell INCISE about your surface, its current coating, exposure and project area. We can help you confirm suitability and plan the treatment.
Talk to INCISE Explore technical resources