INCISE ACADEMY / APPLICATION GUIDES

INCISE Metallic application guide

INCISE Metallic™ is a ready-to-use, water-based decorative mineral metallic coating for walls and furniture. A fine trowel pass leaves broad, quiet shifts in tone; a brush or patterned roller breaks the reflection into smaller marks. Choose from 16 metallic colours and approve the finish in the light it will be seen in.

Bronze metallic feature wall in a hotel reception

Specify for residential feature walls, restaurant dining rooms, hotel receptions, shops and showrooms. For exterior and wet-area walls, confirm the substrate, exposure and complete protective system with INCISE. The decorative coating does not replace the waterproofing beneath it.

Go to the application steps
BEFORE YOU BEGIN

Choose the reflection first.

Look at the sealed sample from the doorway, then along the wall. Side lighting picks up ridges that are barely visible head-on. Agree the colour, stroke and sheen before work begins.

Tools for the wall

Moisture meter, masking materials, roller and tray for primer, clean finishing trowel or spatula, brush or patterned roller, sanding and polishing tools, dust removal equipment and a clean sealer roller.

Air below 30°C; relative humidity no higher than 60%. Avoid wet walls, rain and direct sun.

ON SITE / SIX STEPS

From primer to protected finish.

01 / Prepare the surface

Use a sound, clean wall. Remove dust, dirt, grease and loose material. Repair cracks and holes with compatible repair materials and let them dry completely. On new or existing mortar and lime plaster, measure moisture: proceed only below 5%. For furniture, confirm adhesion on the actual substrate.

02 / Roll on Metallic Primer

Apply one even coat of INCISE Metallic Primer by roller. Use the dedicated Metallic Primer rather than Primer X WB. Allow 1–2 hours to dry. Check corners and edges for missed areas before coating.

Rolling Metallic Primer onto plaster

03 / Lay the first decorative coat

INCISE Metallic is supplied ready to use; there is no mixing ratio. Apply lightly with a trowel, spatula or brush. Work to the approved sample and avoid heavy pressure, which can change the way the surface catches light.

Applying bronze metallic coating with a trowel

04 / Build coverage and texture

Allow 30–60 minutes between decorative coats. Apply the second coat so the substrate no longer shows through. To make a pattern, let the fresh material set slightly, then work it with a trowel or decorative roller, typically after 5–10 minutes. Match the direction and scale of the approved sample.

Forming a repeat pattern with a decorative roller

05 / Dry, sand and polish

Leave the completed decorative coats for at least 48 hours before sanding and polishing. Match the sample and take care at raised details and edges. Remove sanding dust before sealing.

06 / Seal and hand over

Apply two coats of INCISE WB Sealer in the approved matt, satin or gloss sheen. Follow the WB Sealer datasheet for the interval between its coats. The Metallic sheet lists 3–4 hours after sealing for drying; confirm full cure before washing or exposing the wall to water.

SPECIFIER NOTES

Packs and coverage

System code
INCISE-MET-001
Primer
INCISE Metallic Primer • 4 kg • approx. 40 m² per bucket
Decorative coat
INCISE Metallic • 4 kg • two coats • stated thickness: 0.5 mm
Metallic yield
Approx. 40 m² per 4 kg. Confirm two-coat yield on the approved sample before ordering.
Protective coats
INCISE WB Sealer • two coats • gloss, matt or satin
Sealer yield, one coat
5 L: approx. 40 m² | 20 L: approx. 150 m²
Sealer yield, two coats
5 L: approx. 20 m² | 20 L: approx. 75 m² before waste
Site conditions
Air below 30°C; relative humidity no higher than 60%. Avoid wet walls, rain and direct sun.
Storage
Store in a cool, dry place. Shelf life: two years.

Handling

Danger. For professional applicators. Causes serious eye damage and skin irritation; may cause skin sensitisation and respiratory irritation. Wear gloves, eye protection and suitable respiratory protection. Ventilate enclosed areas and control sanding dust. Avoid contact with eyes, skin and mucous membranes. For eye contact, rinse with water for 15 minutes and seek immediate medical attention. For skin contact, wash with soap and water and remove contaminated clothing. Refer to the INCISE Metallic safety data sheet.

Discuss a Metallic sample with INCISE