INCISE ACADEMY / APPLICATION GUIDE

INCISE Cemwash application guide

INCISE Cemwash is a premium textured mineral microcement for interior and exterior walls. Refined cementitious binders and mineral pigments give the surface its colour; the applicator gives it its pattern. A brush leaves fine lines that catch side light. A cloth leaves a softer, broken impression. Both belong to the same continuous mineral finish.

Explore six textures
Textured mineral wall in a dining interior

Choose the finish in the light it will live in.

Make a sample on the specified background. Mark the tool and stroke direction, seal part of the panel, and inspect it both face-on and in raking light. Agree how pronounced the relief should be before the applicator starts the full elevation.

Indicative coverage: 3–5 m²/kg, depending on texture. Establish actual consumption on a measured trial panel using the intended coats and tool. The nominal total system thickness is approximately 1–2 mm.

Tools and batch preparation

Block brush or broom, sponge, texture roller, clean plastic trowel, stencils and textured cloth; clean pails, measuring equipment, mixer, fine abrasive, dust-removal tools and a fine-mist sprayer where curing requires it.

The specified mix ratio is 1:2. The source sheet does not define the measuring units or component order; confirm the batch measure with INCISE Technical before mixing. Use clean water, measure each batch the same way and mix thoroughly to a consistent slurry.

How to apply INCISE Cemwash

Start low and work upwards when coating, mist curing and sealing. A controlled upward pass keeps wet material on the tool and helps prevent drops and streaks.

01 Prepare the wall

Start with clean, dry, sound cement plaster, concrete, render, brick or blockwork. On painted walls, remove loose or poorly bonded coatings, then confirm adhesion on a trial area. Remove grease and dust, repair defects and even out the background. Allow new plaster at least 28 days to cure.

Site check: Proceed when the wall is stable and even. Texture will not correct a failing base.

02 Prime with INCISE Primer X

Apply INCISE Primer X evenly over the prepared wall and allow it to dry completely. Check corners, returns and repaired patches for missed areas.

Site check: The primer is dry across the whole panel before the mineral coat begins.

03 Mix and apply the first coat

Mix a consistent batch. Start at the bottom of the panel and work upwards with a block brush or broom; spray where the approved sample calls for it. Load the tool lightly enough to hold the slurry and maintain a wet edge.

Site check: Check each lift for runs, drips and uneven loading before moving higher.

04 Cure between coats

Protect the wall from rain and excessive sun. Allow 12–24 hours between coats and wait until the coat is dry. If light mist curing is needed, start at the bottom and move upwards in controlled passes. Do not saturate the wall or let water run down the face.

Site check: Wait until the first coat is dry and firm. Lightly sand isolated high points only if needed; remove dust.

05 Form the second-coat texture

Apply the second coat from bottom to top. Work manageable panels and texture the material while workable. Repeat the tool angle, pressure and sequence from the approved sample. At corners and stops, finish the pattern deliberately rather than doubling up the relief.

Site check: Review the wall from normal viewing distance and in side light. Let the final coat dry thoroughly.

06 Seal and protect the relief

Lightly sand only unwanted nibs, if required, and remove dust. Apply 2–3 coats of the selected INCISE sealer from bottom to top. Work in thin, even passes; keep sealer out of recesses where it could pool. Follow the selected sealer’s drying, recoating and service times.

Site check: Check for streaks and missed recesses. Protect the finish until the sealer is ready for use.

INCISE ACADEMY / VIDEO GUIDE

Watch the Cemwash application.

Use the film alongside the six steps. Pay attention to tool direction and how the texture reads as the applicator moves across the wall.

Watch on YouTube

Six ways to move the mineral.

These illustrated tool studies show the kind of mark each tool can leave. Choose the final texture from a sealed physical sample.

Brush grain on a textured mineral wall

Brush grain

Draw a block brush or fine broom upwards. Keep the spacing and direction of the grain consistent.

Broken relief on a textured mineral wall

Broken relief

Pass a clean plastic trowel lightly across fresh texture to flatten the peaks while retaining the hollows.

Stencil relief on a textured mineral wall

Stencil relief

Hold a stencil flat against the sample, apply sparingly and lift cleanly. Set the repeat before starting the wall.

Textile impression on a textured mineral wall

Textile impression

Press and lift a textured cloth without dragging. Rotate it between impressions to soften the repeat.

Mineral stipple on a textured mineral wall

Mineral stipple

Dab with a sponge, changing its orientation. Pressure determines the density of the stipple.

Rolled pattern on a textured mineral wall

Rolled pattern

Roll texture upwards in adjacent passes. Align the pattern at each overlap rather than rolling twice over the join.

Protect the texture you approved.

INCISE WB Sealer: general-purpose protection. INCISE PU WB Sealer: for greater durability and stain resistance. INCISE Silicone Sealer: water repellency, particularly for exterior applications. Approve tone and sheen on the sealed sample.

Discuss a Cemwash sample