Technical resources / Application guides

INCISE ThermoShield

Textured protection for walls that face the elements.

INCISE ThermoShield TPC is a ready-to-use, water-based thermoplastic textured coating for interior and exterior wall and ceiling protection. Thermoplastic acrylic binders, reinforced mica and silica fillers, and UV-stable pigments form a tough, flexible protective film with weather resistance, surface reinforcement and heat-reflective properties.

Follow the application Talk to INCISE
2 coatsStandard minimum
6 - 10 m²/LPer coat
4 - 6 hoursBetween coats
7 daysFull cure

Understand the system

What is INCISE ThermoShield?

INCISE ThermoShield TPC is a ready-to-use, water-based thermoplastic textured coating for interior and exterior wall and ceiling protection. Thermoplastic acrylic binders, reinforced mica and silica fillers, and UV-stable pigments form a tough, flexible protective film with weather resistance, surface reinforcement and heat-reflective properties.

Designed for exterior masonry, cement plaster and render, concrete facades, industrial buildings and warehouses, commercial developments, residential housing, schools and hospitals, and interior ceilings exposed to radiant heat. It supports facade durability, reduced surface heat gain, crack bridging and surface reinforcement.

Its textured matt finish combines decorative character with protective performance. Choose it for facade protection and the stated heat-reflective properties; select the complete system to suit the substrate and exposure.

Prepare your tools. Prepare your surface.

Use a brush, sponge roller or lamb’s wool roller, clean stirring equipment and suitable protective equipment. The substrate must be clean, dry and sound. Repair cracks and prime porous surfaces before coating. For the reinforced route, add fiberglass mesh and an embedding tool.

Standard protective coating

From preparation to protection.

Read the product TDS and SDS before starting. Follow these steps for the standard minimum two-coat application.

Step 01

Prepare the surface

Start with a clean, dry, structurally sound substrate. Remove contamination and repair cracks before coating. Surface preparation determines the quality of adhesion and the consistency of the textured finish. Do not use the coating to conceal unresolved substrate defects.

Step 02

Prime and organise the tools

Prime porous surfaces with INCISE Primer. Use a brush or a sponge or lamb’s wool roller for the coating. Have clean stirring equipment, masking materials and suitable access equipment ready. Wear appropriate PPE and avoid skin and eye contact. Consult the Safety Data Sheet for full precautions.

Step 03

Stir and apply the first coat

INCISE ThermoShield TPC is supplied ready to use. Stir thoroughly before application. Apply evenly with a brush or roller, maintaining a consistent texture without over-spreading. Work within the stated application temperature of 10 - 35°C. Avoid application during rain.

Step 04

Allow drying, then apply the second coat

Allow 4 - 6 hours before recoating under the stated typical conditions. Apply the second coat evenly to achieve complete coverage and a consistent textured matt finish. The standard system requires a minimum of two coats. Touch dry is typically 1 - 2 hours; this is not the recoat time.

Step 05

Allow full cure and check the finish

Allow 7 days for full cure. Check the completed coating for continuity, missed areas and consistent texture. Drying and performance vary with substrate quality and application conditions. Keep the application and curing sequence aligned with site conditions and INCISE technical guidance.

Separate reinforced route

ThermoShield WP

Primer layer: apply INCISE Primer or diluted ThermoShield. Apply the first ThermoShield coat and embed fiberglass mesh into the wet coating. Apply a second coat to encapsulate the mesh, followed by a finishing coat for full coverage. When used beneath screed, clean sand may optionally be broadcast onto the wet surface. The supplied datasheet does not specify a dilution ratio or a separate reinforced-system consumption rate; obtain these project details from INCISE before starting this route.

The reinforced ThermoShield WP route is for light-duty waterproofing in suitable non-critical, non-ponding areas. It is not suitable for ponding water, water-retaining structures or negative-pressure waterproofing, and is not a substitute for structural waterproofing membranes.

Plan the quantity. Keep the texture consistent.

INCISE ThermoShield covers 6 - 10 m² per litre per coat. For two coats, allow approximately 0.20 - 0.33 L/m² before wastage. A 5 L pack covers approximately 15 - 25 m² of finished two-coat area; a 20 L pack covers approximately 60 - 100 m². Porosity and texture change consumption. These figures do not establish a reinforced waterproofing specification.

Colour for the whole elevation.

Urban White, Sahara Ivory, Desert Cream, Jasmine Glow, Concrete Grey, Slate Horizon, Charcoal Edge, Terracotta Clay, Cocoa Earth and Savannah Green. Custom colours are available on request.

Explore colours

Questions before you begin.

Is INCISE ThermoShield ready to use?

Yes. It is supplied ready to use in 5 L and 20 L packs. Stir thoroughly. The separate WP primer option refers to diluted ThermoShield; obtain its dilution instructions from INCISE.

Can I use ThermoShield inside and outside?

Designed for exterior masonry, cement plaster and render, concrete facades, industrial buildings and warehouses, commercial developments, residential housing, schools and hospitals, and interior ceilings exposed to radiant heat. It supports facade durability, reduced surface heat gain, crack bridging and surface reinforcement.

Is ThermoShield a structural waterproofing membrane?

The reinforced ThermoShield WP route is for light-duty waterproofing in suitable non-critical, non-ponding areas. It is not suitable for ponding water, water-retaining structures or negative-pressure waterproofing, and is not a substitute for structural waterproofing membranes.

How long between ThermoShield coats?

The typical recoat time is 4 - 6 hours. Touch dry is 1 - 2 hours and full cure is 7 days. These values depend on application conditions and substrate quality.

What texture does ThermoShield produce?

INCISE ThermoShield produces a high-build textured matt finish applied with a brush, sponge roller or lamb’s wool roller. Approve the colour and texture on a sample before proceeding over a large elevation.

Specify the right protection.

Send INCISE your substrate, project location, area and exposure conditions so the team can advise on the appropriate coating route.

Discuss your project Technical resources

Application and finished-surface images are illustrative visualisations.